Advertising
Manual Whirlpool Wfe 61a.pdf. Whirlpool - WFE540H0ES - 6.4 cu. Freestanding Electric. Whirlpool WFE540H0ES WFE540H0ES 6.4 Cu.Ft. Stainless 5 Burner.
A
B
D
F
E
C
30' (76 cm) Freestanding Electric Range
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
GFE461LV
GFE471LV
WFE301LV
WFE361LV
WFE364LV
GFE471LV
WFE301LV
WFE361LV
WFE364LV
WFE366LV
WFE371LV
WFE374LV
WFE381LV
WFE371LV
WFE374LV
WFE381LV
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Instructions packed with product. Specifications subject to change without notice.
Electrical: Range must be connected to the
proper electrical voltage and frequency as
specified on the model/serial number rating plate.
The model/serial number rating plate is located
behind the control panel or on the oven frame
behind the storage drawer panel. Refer to the
figures in the “Product Dimensions” section.
proper electrical voltage and frequency as
specified on the model/serial number rating plate.
The model/serial number rating plate is located
behind the control panel or on the oven frame
behind the storage drawer panel. Refer to the
figures in the “Product Dimensions” section.
This range is manufactured with the neutral
terminal connected to the cabinet. Use a 3-wire,
UL listed, 40- or 50-amp power supply cord
(pigtail). If local codes do not permit ground
through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and
investigated for use with ranges.
terminal connected to the cabinet. Use a 3-wire,
UL listed, 40- or 50-amp power supply cord
(pigtail). If local codes do not permit ground
through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and
investigated for use with ranges.
A circuit breaker is recommended.
The range can be connected directly to the circuit
breaker box (or fused disconnect) through
flexible or nonmetallic sheathed, copper or
aluminum cable.
breaker box (or fused disconnect) through
flexible or nonmetallic sheathed, copper or
aluminum cable.
CABINET OPENING DIMENSIONS
®
*NOTE: 24' (61 cm) min. when bottom of wood
or metal cabinet is protected by not less than 1/4' (6.4 mm)
flame retardant millboard covered with not less than No. 28
MSG sheet steel, 0.015' (0.4 mm) stainless steel, 0.024' (0.6
mm) aluminum or 0.020' (0.5 mm) copper.
flame retardant millboard covered with not less than No. 28
MSG sheet steel, 0.015' (0.4 mm) stainless steel, 0.024' (0.6
mm) aluminum or 0.020' (0.5 mm) copper.
30' (76.2 cm) min. clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal
cabinet.
platform and the bottom of an unprotected wood or metal
cabinet.
Cabinet opening dimensions shown are for:
25' (63.5 cm) countertop depth,
24' (61 cm) base cabinet depth,
36' (91.4 cm) countertop height
24' (61 cm) base cabinet depth,
36' (91.4 cm) countertop height
Ref. W10196158
07-30-08
A. 27
¹⁷⁄₃₂' (69.9 cm) max. depth with handle
B. 46
⁷⁄₈
' (119.1 cm) overall height (max.) with leveling legs
screwed all the way in*
C. 36' (91.4 cm) cooktop height (max.) with leveling legs screwed
all the way in*
D. 29
⁷⁄₈' (75.9 cm) width
E. 25' (63.5 cm) depth
F. Model/serial rating plate (located on the left side frame behind
storage drawer panel)
A
B
C
D
E
F
*Range can be raised
approximately 1'
(2.5 cm) by adjusting
the leveling legs.
(2.5 cm) by adjusting
the leveling legs.
A. 13' (33.0 cm) max. upper cabinet depth
B. 30' (76.2 cm) min. opening width
B. 30' (76.2 cm) min. opening width
C. For minimum clearance to top of cooktop, see NOTE*.
D. 30
D. 30
¹⁄₈' (76.5 cm) min. opening width
E. Outlet - 8' (20.3 cm) to 22' (55.9 cm) from either cabinet,
![Manual Manual](/uploads/1/2/5/2/125218888/243303493.jpeg)
5
¹⁄₂' (14.0 cm) max. from floor
F.
⁷⁄₈' (2.2 cm) min. required between cutout and cabinet door or
hinge.
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Electrical Requirements - U.S.A. Only
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
1 Batterymarch Park
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as to
whether the appliance is properly grounded. Do not modify the
power supply cord plug. If it will not fit the outlet, have a proper
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
■Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial rating plate.
The model/serial rating plate is located on the frame behind a
top corner of the door or either side of the drawer. Refer to
the figures in “Product Dimensions” in the “Location
■This range is manufactured with the neutral terminal
connected to the cabinet. Use a 3-wire, UL listed, 40- or
50-amp power supply cord (pigtail) (see the following Range
Rating chart). If local codes do not permit ground through the
neutral, use a 4-wire power supply cord rated at 250 volts,
40 or 50 amps and investigated for use with ranges.
*The NEC calculated load is less than the total connected load
**If connecting to a 50-amp circuit, use a 50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1³⁄₈' (34.9 mm) diameter connection opening.
■The range can be connected directly to the circuit breaker
box (or fused disconnect) through flexible or nonmetallic
sheathed, copper or aluminum cable. See the “Electrical
■Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that
the range can be moved if servicing is ever necessary.
■A UL listed conduit connector must be provided at each end
of the power supply cable (at the range and at the junction
■Wire sizes and connections must conform with the rating of
■The wiring diagram is located on the Tech Sheet.
■The Tech Sheet is located on the back of the range inside a
If connecting to a 4-wire system:
This range is manufactured with the ground connected to the
neutral by a link. The ground must be revised so the green
ground wire of the 4-wire power supply cord is connected to the
cabinet. See “Electrical Connection - U.S.A. Only” section.
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord (pigtail) must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50P plug on the
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
The minimum conductor sized for the copper 4-wire power
40-amp circuit
1 No.-10 white neutral
If connecting to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
Power Supply Cord Kit
120/240 Volts120/208 VoltsAmps
16.6 - 22.5 KW
12.6 - 18.5 KW
50
3-wire receptacle (10-50R)